Table of Contents Table of Contents
Previous Page  179 / 179
Information
Show Menu
Previous Page 179 / 179
Page Background

Automatic Valve warrants its products to be free from defect in material or workmanship over a period of 18 months from

the date of shipment from its factory. Automatic Valve will, at its option, either repair or replace the non-conforming product

at no charge upon return of the product with transportation prepaid.

Automatic Valve will replace standard commercial grade NEMA 4 solenoid coils which fail due to burnout when operated

within their rated capacity or voltage.

Automatic Valve is not responsible for damage to its products through improper installation, maintenance, use, repairs or

operating beyond rated capacity of voltage, intentional or otherwise. Automatic Valve is not liable for claims for labor, loss

of profit or good will, repairs, delay damages, direct or indirect penalties, or expenses incidental to replacement. The buyer,

by acceptance of delivery, assumes all liability for the product’s use or misuse in the as-shipped condition.

Automatic Valve, recognizing its goal of continuous improvement, reserves the right to discontinue or change specifications,

products or prices without incurring obligation.

Precautions

Warranty

Applications:

Automatic Valve manufactures general purpose, industrial pneumatic and vacuum service valves, which

are not inherently harmful. However, the control systems in which they operate must have safeguards to prevent injury or

damage in case of system component failure.

OSHA 1910.217, dated November 1, 1975, ANSI B11.1, Revision 1982, and EN 13736: 1999 specifically recommend special

purpose dual (double) safety clutch and brake valves for power presses. Automatic Valve does not manufacture special

purpose dual safety valves for presses. Do not use Automatic Valve Corp’s valves for power presses.

Two position valves, whether they are 2 way, 3 way, or 4 way, will always have a flow path from the valve’s inlet port or

ports to one of the outlets, regardless of which of the two positions is used. If air trapped in or exhausted from the ports

presents a hazard in operation or in servicing the system, a separate method must be provided to exhaust this air or the

valve should not be used.

Three position 3 way and 4 way valves, whether solenoid operated, air piloted or manually operated, can move to the center

position if the operators are not actuated. If air trapped in or exhausted from the ports presents a hazard in operation or in

servicing the system, a separate method must be provided to exhaust this air or the valve should not be used.

Some solenoid and air piloted valves incorporate manual overrides. Manual overrides, when activated, shift the valve as if

the solenoid or air pilot were actuated. If accidental or intentional operation of the manual override could cause a dangerous

problem, valves without a manual override should be used.

Use valves only within specification limits listed in our catalog.

Installation:

Consult the Engineering and Maintenance section of the Automatic Valve catalog #0001-001 for installa-

tion instructions. Do not install valves without first turning off air and electricity. Valves must be installed by qualified and

knowledgeable personnel who understand how specific valves are to be piped and electrically connected. Do not install

valves unless the valves’ flow path, as described by ANSI and ISO symbols in our catalog, conform to the application’s design

specifications.

Maintenance:

Disconnect air and electricity and bleed all pressurized lines before removing two and three position valves.

Consult the Engineering and Maintenance section of the Automatic Valve catalog #0001-001 for maintenance instructions.

Servicing should only be undertaken by qualified and knowledgeable personnel who understand the function and operation

of specific valves. Care must be followed to prevent damage to valves caused by stepping on them, dropping them or hitting

them with any object. Damaged valves should be returned to Automatic Valve for inspection and rebuilding.

Form # 0001-001 Rev K CN9773 3M © 2011 Printed in the USA

W

o

r

l

d

C

l

a

s

s

P

n

e

u

m

a

t

i

c

S

o

l

u

t

i

o

n

s

A

U

T

O

M

A

T

I

C

V

A

L

V

E

World Class Pneumatic Solutions

I.

www.automaticvalve.com

T. 248.474.6700

E.

avc@automaticvalve.com

F. 248.474.6732

AUTOMATIC VALVE

41144 Vincenti Court Novi, MI USA 48375-1922

Automatic Valve Corp